DiskMend

Updated 2026-11-15 · 4 min read

SD card not showing up on Windows? How to fix it without losing data

SD card not detected, not showing in File Explorer, or asking to be formatted? Find the cause step by step and get your photos back before you format or repair anything.

You insert an SD or microSD card and nothing happens, or the card appears without a drive letter, or Windows says it must be formatted. The cause can be as simple as a loose adapter or as serious as a failed card controller, and the right fix depends on which one it is.

Work through the checks below in order. None of them writes to the card, so your photos stay safe while you find out what is wrong.

1. Rule out the hardware around the card

  • Try another card reader or another USB port, ideally directly on the computer instead of a hub.
  • If you use a microSD-to-SD adapter, try a different adapter; they wear out and lose contact.
  • Check the lock switch on full-size SD cards. A locked card is still detected but cannot be written to.
  • Try the card in a camera or phone to see whether it is detected there.

2. Look in Disk Management

Right-click Start › Disk Management. Find a removable disk with the card’s size. What you see there tells you what to do next:

  • Healthy partition but no letter: right-click › Change Drive Letter and Paths › Add. The files appear in File Explorer.
  • RAW file system: Windows cannot read the file system. Do not format; recover the files first.
  • Unallocated: the partition table is damaged or was erased. The files are usually still on the card.
  • No Media or 0 bytes: the card’s controller does not answer. This is a hardware failure.
  • Not listed at all: try the hardware checks again or check Device Manager for errors.

3. RAW or unreadable cards: recover before you repair

A RAW card has a damaged boot sector or file table, but the photos and videos are still in its memory. Formatting, chkdsk or the “Scan and fix” prompt would write new structures over what is left.

Recovery software reads the card directly without Windows needing to mount it. DiskMend tries the backup boot records of FAT32 and exFAT first, then the old file tables, and finally searches the whole card for photo and video formats such as JPEG, HEIC, CR3, MP4 and MOV.

When software cannot help

If the card shows as 0 bytes, “No Media”, has a much smaller size than printed or is not detected in any device, the controller inside it has usually failed. Software can only read what the controller passes on. For important photos, a data recovery lab can read the memory chip directly; it is expensive but often successful.

Step by step

  1. 1

    Change reader, adapter and port

    Rule out the hardware between the card and the computer.

  2. 2

    Open Disk Management

    Check whether the card is listed, its size and its file system.

  3. 3

    Assign a drive letter if missing

    Right-click the partition › Change Drive Letter and Paths › Add.

  4. 4

    Do not format a RAW card

    Close the format prompt and do not run chkdsk.

  5. 5

    Scan the card

    Select the card in a recovery tool and run a full scan.

  6. 6

    Save to the computer

    Save the recovered photos to the PC’s disk, then format the card if you want to keep using it.

What Disk Management tells you about the card
Disk Management showsMeaningWhat to doData recoverable
Partition, no drive letterLetter not assignedAdd a drive letterFiles are fine
RAWFile system damagedRecover, then formatUsually
UnallocatedPartition table lostRecover with a full scanUsually
No Media / 0 bytesController failureData recovery labNot with software
Not listedReader, adapter or card failureTry other hardwareDepends

Frequently asked questions

Why is my SD card not showing up?+

Common causes are a faulty reader or adapter, a missing drive letter, a damaged file system (RAW) or a failed card controller. Disk Management shows which one it is.

How do I fix an SD card without formatting it?+

Assign a drive letter if it is missing. If the card is RAW, recover the files first; formatting is the last step, not the first.

Can I recover photos from a RAW SD card?+

Usually yes. The photos are still in the card’s memory; recovery software reads them directly even though Windows cannot open the card.

What does it mean if the card shows 0 bytes?+

The card’s controller is not reporting its memory. This is a hardware fault that software cannot repair or read through.

Should I run chkdsk on the SD card?+

Not before recovering. chkdsk can remove damaged entries and make some files impossible to recover.

Guides

More guides

Guides →