DiskMend

Updated 2026-11-19 · 6 min read

“Drive Is Not Accessible. The Parameter Is Incorrect”: Fix It Without Losing Your Files

Windows says E:\ is not accessible and the parameter is incorrect? The file system is usually damaged, not your files. Check the connection, recover your data first, then repair the drive.

You plug in a USB drive, SD card or external hard drive, double-click it, and Windows answers with “E:\ is not accessible. The parameter is incorrect.” The drive may show in File Explorer, yet nothing opens.

The message sounds technical but it points to a simple situation: Windows can see the drive but cannot make sense of its file system. Your files are very often still there. What you do in the next few minutes decides whether they stay that way.

What the error means

The code behind the message is 0x80070057, Windows’ way of saying that a request had an invalid parameter. On a drive it appears when the file system’s own records, such as the boot sector or the table that lists files, are damaged or unreadable. The data blocks holding your files are usually untouched.

The most common triggers are unplugging the drive without safely removing it, a power cut during writing, a loose or worn cable, bad sectors, a faulty USB port, or a partition table damaged by a failed format or repartition.

Step 1: rule out the connection

Remove the drive, wait a few seconds and connect it to a different USB port directly on the computer, not through a hub. Try a different cable, and for a 3.5-inch external drive make sure its power adapter is connected. Then try the drive on another computer. If it opens normally there, the problem was the port, the cable or the driver and not the drive.

Step 2: look at the drive in Disk Management

Right-click Start and open Disk Management. Find the drive in the lower pane. If it shows a file system (NTFS, exFAT or FAT32) and Healthy, the file system is damaged only partly. If it shows RAW, or a black Unallocated area, the file system records cannot be read and Windows will offer to format it. Do not accept.

Note the drive’s size; if it shows 0 bytes or the wrong capacity, see our guide on USB drives with the wrong capacity.

Step 3: get your files out before repairing

Run chkdsk E: without any switch, with your own drive letter. Without /f or /r it only checks and reports, so it is safe. If it reports file system errors or says the volume is RAW, protect your data before any repair. The repair option, chkdsk /f, rewrites the file system structures and can make later recovery harder, as explained in our CHKDSK guide.

Scan the drive with recovery software and save the files to another drive. DiskMend reads the damaged drive without writing to it. When the main boot record or file table is unreadable it tries the backup copies that NTFS, FAT32 and exFAT keep, lists deleted and existing files, and searches the free space by content as a last resort. You can preview what is found before deciding on a license.

Step 4: repair or reformat once the files are safe

When your files are on another drive, running chkdsk E: /f is reasonable and often fixes the problem. If the drive still fails, format it in Disk Management or File Explorer with a quick format and copy the files back. If the error returns on different computers and cables, the drive itself may be failing; replace it and keep the recovered copy.

Step by step

  1. 1

    Do not format

    Ignore the Windows prompt to format the drive until your files are safe.

  2. 2

    Change port, cable and computer

    Connect the drive directly to another USB port, with another cable, or to another PC.

  3. 3

    Check Disk Management

    See whether the drive shows NTFS, exFAT or FAT32, or RAW or Unallocated.

  4. 4

    Run a read-only check

    Run chkdsk E: without /f to see whether the file system has errors.

  5. 5

    Recover your files

    Scan the drive with recovery software and save the files to a different drive.

  6. 6

    Repair or format

    Only now run chkdsk E: /f or format the drive, then copy the files back.

What you see and what to do
Disk Management showsMeaningAction
NTFS / exFAT / FAT32, HealthyFile system partly damagedRecover first, then chkdsk /f
RAWFile system cannot be readRecover first, then format
UnallocatedPartition table damaged or partition deletedRecover first; see lost partition guide
Drive not listedConnection, driver or hardware problemOther port, cable or computer
0 bytes or wrong sizeController or capacity problemDo not write to it; scan for files

Frequently asked questions

What does “The parameter is incorrect” mean on a drive?+

Windows tried to read the drive’s file system and received an invalid response, usually because the file system records are damaged. It does not mean the files have been deleted.

Will formatting fix the error?+

A format creates a new, empty file system and clears the error, but the original file table is gone and recovery becomes harder. Recover the files first, then format.

Is chkdsk safe to run on a drive that is not accessible?+

chkdsk E: without switches is read-only and safe. chkdsk E: /f writes changes to the file system, so run it only after your files are copied or recovered.

Why does the drive work on another computer?+

That points to the USB port, cable, driver or power supply of the first computer rather than damage to the drive.

Can DiskMend recover files from a drive that says the parameter is incorrect?+

Yes. DiskMend reads the drive directly without writing to it, uses backup boot records when the main one is damaged and searches the drive by content when the file table is gone.

Guides

More guides

Guides →