DiskMend

Updated 2026-11-19 · 7 min read

How to Recover Files from a Windows PC That Won’t Boot

Windows won’t start but your files matter? Connect the drive to another PC or copy from the recovery environment, and scan it with recovery software if files are missing. Do not reinstall first.

Your PC stops at a black screen, loops through “Automatic Repair” or shows a blue screen on every start. The first instinct is to reinstall Windows, and that is the one move that can turn a fixable problem into permanent data loss.

In most cases the drive is fine and only Windows is broken, so your documents, photos and projects are still there. This guide shows three safe ways to get them out, from the easiest to the most thorough, and which mistakes to avoid on the way.

First: is it the drive or Windows?

Open the firmware setup screen (usually Del, F2 or F10 right after power-on) and look for your drive in the boot or storage list. If the drive is listed, the hardware is detected and the problem is most likely in Windows, which is the good case.

If the drive is not listed at all, reseat the cable or M.2 connector and check again. If it still does not appear, or if you hear clicking, grinding or repeated spin-up sounds, power the PC off and do not keep trying: every attempt stresses a failing drive. Skip to the section about failing drives.

Option 1: connect the drive to another computer

This is the easiest and safest method because the broken Windows is never started. Remove the drive from the PC (or the laptop’s bottom panel) and connect it to a working computer. A 2.5-inch or 3.5-inch SATA drive needs a SATA-to-USB adapter, and an M.2 NVMe drive needs an NVMe USB enclosure; check the connector type before buying.

The drive appears in File Explorer as an extra drive letter. Copy your Documents, Desktop, Pictures and any other folders under Users\YourName to the working computer or to an external drive. If Windows says you do not have permission to open a folder, click Continue; if access is still denied, open the folder’s Properties › Security tab and take ownership.

If the drive is locked and asks for a recovery key, it is encrypted with BitLocker. Without the key the data cannot be read, so look for the key in your Microsoft account before doing anything else.

Option 2: copy files from the Windows Recovery Environment

If you have no second computer, use the recovery tools that Windows starts by itself after failed boots. On the “Automatic Repair” screen choose Advanced options › Troubleshoot › Advanced options › Command Prompt. Plug in an external drive first.

Drive letters in this environment often differ from what you know: the Windows volume is frequently not C:. Run diskpart, then list volume, and note which letter holds your Windows files and which one is your external drive. Type exit to leave diskpart.

Then copy a folder with robocopy, replacing the letters and the user name:

robocopy C:\Users\YourName\Documents E:\Rescue\Documents /E /R:1 /W:1

The /E switch includes all subfolders, and /R:1 /W:1 makes robocopy retry an unreadable file only once instead of waiting for minutes. Repeat the command for Desktop and Pictures.

Option 3: scan the drive with recovery software

If the folders are empty, files are missing, or Windows reports the drive as RAW or asks you to format it, copying is not enough and the drive needs a scan. Connect it to a working computer as in option 1 and start DiskMend.

DiskMend lists the attached disks, and Windows asks for administrator permission because reading a physical disk requires it. The program only reads the drive and never writes to it. It reads the file system directly, falls back to the backup boot records when the main one is damaged, and searches the free space by content for files whose records are gone. You can scan and preview what is found before deciding on a license, and recovered files must be saved to a different drive than the one you are scanning.

What not to do

Do not reinstall Windows, use “Reset this PC” or run a clean install over the old system. Do not run chkdsk /f or /r on a drive you have not copied yet; it rewrites file system structures and can destroy what recovery software could still read. Repeated Automatic Repair attempts also change the system volume.

Never save recovered files onto the same drive you are recovering from. Use a second drive with enough free space.

If the drive is failing

Clicking, long freezes, files that copy slowly and then fail, or a drive that vanishes and returns are signs of failing hardware. Physical damage such as clicking heads needs a professional data recovery lab, and software cannot repair it.

If the drive is only slow or shows read errors, make a complete copy first and recover from the copy so the weak drive is read once. See our guide on recovering data from a failing hard drive by making a disk image.

Step by step

  1. 1

    Power off and stop retrying

    Shut the PC down and do not reinstall or reset Windows.

  2. 2

    Check that the drive is detected

    Open the firmware setup and confirm the drive is listed. Clicking or a missing drive means stop and use a lab or a disk image.

  3. 3

    Connect the drive to a working computer

    Use a SATA-to-USB adapter or an NVMe enclosure and open the drive in File Explorer.

  4. 4

    Copy your folders

    Copy Documents, Desktop, Pictures and other folders under Users to a different drive.

  5. 5

    Use the recovery environment if you have no second PC

    Open Command Prompt from Advanced options, find the drive letters with diskpart and copy folders with robocopy.

  6. 6

    Scan if files are missing

    Scan the drive with recovery software and save the results to another drive.

Symptoms and the safest next step
What you seeLikely causeSafest next step
Automatic Repair loop or blue screenDamaged Windows files or driversConnect the drive elsewhere and copy files
Drive not listed in firmware setupLoose connector or failed driveReseat once; if still missing, stop and use a lab
Clicking or grinding noisesPhysical damagePower off; professional recovery
Drive asks for a recovery keyBitLocker encryptionFind the key in your Microsoft account
Drive shows as RAW or asks to be formattedDamaged file systemDo not format; scan with recovery software
Folders empty after repair attemptsFiles deleted or hidden by a resetScan the drive with recovery software

Frequently asked questions

Can I recover files from a computer that won’t turn on or boot?+

Usually yes. If the drive is detected, the files are normally intact and can be copied from another computer or from the recovery environment. If the computer shows no sign of power, the problem is often the power supply or motherboard and the drive itself can still be removed and read.

Will reinstalling Windows delete my files?+

A clean install formats or overwrites the system partition and can destroy the files on it. Copy your files first; a repair install that keeps files is not guaranteed to work on a PC that cannot boot.

Do I need a USB adapter to recover files from a laptop that won’t boot?+

An adapter or enclosure is the easiest route because it lets a working computer read the drive. Without one you can copy files from the Command Prompt in the Windows Recovery Environment to an external drive.

Is it safe to run chkdsk on a drive that will not boot?+

Not before your files are safe. chkdsk with /f or /r modifies the file system and can make later recovery harder. Copy or scan first.

Can DiskMend recover files from a drive that will not boot?+

Yes, when the drive is connected to a working Windows computer as an extra disk. DiskMend reads the drive without writing to it and finds existing, deleted and formatted files; it does not repair Windows itself or decrypt BitLocker drives.

Guides

More guides

Guides →