DiskMend

Updated 2026-11-19 · 6 min read

How to Recover Deleted RAW Photos (CR2, CR3, NEF, ARW, DNG) from a Camera Card

Deleted or lost RAW photos from a camera memory card are often still on the card. Learn what to do first, which RAW formats recovery software can find, and how to save them safely.

You deleted the wrong folder in the camera, formatted a card that was not backed up, or the card suddenly shows as empty or unreadable. For a photographer that can mean an entire shoot, and RAW files are the ones you never want to lose.

The good news is that deleting or formatting rarely erases the image data at once. The bad news is that every new photo you take can overwrite it. This guide explains what to do in the first minutes, how recovery of RAW files works and what to expect.

What happens when a photo is deleted

A memory card has a file system, usually FAT32 or exFAT, that works like a table of contents. When you delete a photo or quick-format the card, the camera removes or resets the entries in that table, but the image data itself stays where it was. The space is only marked as free.

That is why recovery is possible, and why time matters: the next photo the camera writes can land exactly on the space of a deleted one. RAW files are large, so a few shots can overwrite many pictures.

First minutes: protect the card

Switch the camera off and remove the card. Do not shoot, review, delete or format anything, and do not insert the card into the camera again to “check”. Do not accept the computer’s offer to format the card if Windows says it needs formatting.

Connect the card to the computer with a card reader or the computer’s card slot, not through the camera’s USB cable. A reader gives direct access to the card and avoids the camera writing to it.

How RAW recovery works

DiskMend first reads the card’s file system and lists the deleted and existing files it can still find with their original names. If the file table was erased by a format or is damaged, it searches the card by content: every RAW format starts with a recognisable structure, so the program can find the files even when no record points to them and works out where each one ends.

Content-based results come back without the original file names, so photos appear as numbered files; the date, camera model and settings stay stored inside each file and show up in your photo software. The program previews RAW files and falls back to the small JPEG preview embedded in most RAW files when the full image cannot be decoded. Previews are reduced in detail; saving full files needs a license, and you decide after seeing what was found.

Supported RAW formats

The table below lists the RAW formats DiskMend finds by content. Photos in JPEG, HEIC, PNG and many video formats are found too.

Save the photos safely

Save the recovered photos to your computer’s drive or an external drive, never back to the card. After recovery, open a few files in your RAW converter to confirm they are complete. A photo that was partly overwritten can show a cut-off image or a grey area; the embedded preview may still show the full frame.

If the card is not recognised at all

If the computer does not show the card, try another reader and port first. A card with read errors should be copied to a disk image before scanning so it is read once. When the card’s controller is dead, only a specialised lab can help.

How to avoid losing photos again

Copy the card to your computer as soon as you finish shooting, before deleting anything. Use two card slots in recording mode if the camera has them, and format the card in the camera, not on the computer, only after the files are safely backed up in two places.

Step by step

  1. 1

    Stop using the card

    Switch off the camera and remove the card; do not shoot or format.

  2. 2

    Connect the card to the computer

    Use a card reader and cancel any format prompt from Windows.

  3. 3

    Scan the card

    Select the card in DiskMend and run the scan; it only reads the card.

  4. 4

    Preview the results

    Check the found RAW files and their previews.

  5. 5

    Save to a different drive

    Select the photos and save them to your computer or an external drive.

  6. 6

    Check the files

    Open the photos in your RAW converter and confirm they are complete.

RAW formats DiskMend finds by content
ExtensionTypically used byNotes
CR2Canon (older EOS models)Found by content, previewed
CR3Canon (newer EOS and R models)Found by content, previewed
NEFNikonFound by content, previewed
ARWSonyFound by content, previewed
DNGAdobe, Leica and other makersFound by content, previewed
ORFOlympus / OM SystemFound by content, previewed
PEFPentaxFound by content, previewed
SRWSamsungFound by content, previewed
RAFFujifilmFound by content, previewed

Frequently asked questions

Can I recover RAW photos after formatting the card in the camera?+

Often yes, if you have not written new photos to the card. A quick format clears the file table but leaves the image data; a content-based scan can find the files, without their original names.

Why do recovered RAW photos have different names?+

File names are stored in the file table. When that table is erased, the files are found by their content and receive new numbered names; the shooting date and camera data remain inside each file.

Will recovered photos be complete?+

Photos whose data was not overwritten come back complete. If new pictures were written over part of a file, it can be partly damaged; the embedded preview often still shows the frame.

Should I put the card back in the camera to check it?+

No. Any write to the card can overwrite deleted photos. Scan it with a card reader on the computer.

Does DiskMend change my memory card?+

No. It only reads the card and saves recovered photos to a different drive.

Guides

More guides

Guides →