DiskMend

Updated 2026-11-19 · 6 min read

Failing Hard Drive? How to Recover Your Data Safely by Making a Disk Image First

A hard drive that is slow, freezing or throwing read errors can fail completely at any time. Learn the warning signs, when to stop, and how to copy the drive once and recover from the copy.

A drive that suddenly takes minutes to open a folder, freezes Windows, disconnects by itself or shows I/O errors is trying to tell you something. Many people react by scanning it again and again, running repair tools, or copying files until the copy stops. Each of those reads puts more wear on a weak drive.

The safer approach, used by professionals, is to read the failing drive as few times as possible: make one careful copy to a healthy drive, then recover from the copy. This guide explains the signs, the limits of software and the procedure.

Signs of a failing drive

Typical signs are folders that open very slowly, copies that stall and then fail, repeated I/O device errors, files that suddenly become unreadable, the drive disappearing and reappearing, Windows freezing when the drive is connected, and a health status of Warning or Unhealthy in the PowerShell command Get-PhysicalDisk. Unusual noises such as clicking or scraping are the most serious sign.

Stop using the drive for anything else. Do not install programs on it and do not leave it running for hours.

When software cannot help

A drive that clicks, is not detected at all, or is not spinning has a mechanical or electronic fault, such as a damaged head or a failed controller. Software cannot repair this, and every power-on can scratch the platters further. Power it off and contact a data recovery lab that has a clean room. Do not open the drive yourself, and do not put it in the freezer.

A drive that is detected, spins normally and only shows read errors or slowness is a candidate for the disk image procedure below.

Why an image comes first

Scanning and recovering need many passes over a drive: the scan, the preview, the saving. On a weak drive each pass risks the final failure. A disk image is a complete, sector-by-sector copy of the drive in a file. Once it exists, the failing drive is read only once, and everything else, including repeated scans, happens on the healthy copy.

How DiskMend creates the image

Connect the failing drive and a second drive with enough free space for a full copy of the failing drive’s capacity. Start DiskMend, select the drive, and when the pre-check finds read errors, choose Create a disk image. DiskMend does not allow saving the image onto the drive being copied.

The copy runs in two passes. In the first, it copies every readable area in large blocks as fast as possible. When a block fails, it skips that block and the area after it, with the skipped stretch growing step by step, because every read in a damaged area is slow and strains the drive. In the second pass, the skipped areas are tried sector by sector. Sectors that really cannot be read stay empty in the image and are recorded as unreadable on a map file.

Because of that map, a stopped copy can be resumed where it left off, and unreadable areas can be tried again later, for example after the drive has cooled down.

Recover from the image

When the image is ready, use Open a disk image and scan it like a drive. DiskMend lists existing, deleted and formatted files and searches by content, exactly as it does on a real drive, but the failing hardware is no longer involved. Save the recovered files to a third location that is neither the failing drive nor the image drive if possible.

Files that lie in unreadable sectors come back partly damaged or not at all; the recovery summary shows which files had unreadable areas. The rest is as complete as the hardware allowed.

After recovery

Replace the drive instead of reformatting and reusing it. A drive that has started to fail rarely recovers. Keep two copies of important data, one of them not connected to the computer.

Step by step

  1. 1

    Check for physical damage

    If the drive clicks, grinds or is not detected, power it off and use a professional lab.

  2. 2

    Prepare a healthy drive

    Connect a second drive with free space equal to the failing drive’s capacity.

  3. 3

    Start the disk image

    In DiskMend select the failing drive and choose Create a disk image; save it to the healthy drive.

  4. 4

    Let both passes finish

    The fast pass copies readable areas; the second pass tries the skipped areas sector by sector.

  5. 5

    Scan the image

    Open the disk image and scan it; the failing drive is no longer needed.

  6. 6

    Save your files

    Save the recovered files to a different drive and keep a second copy.

Symptoms and what to do
SymptomLikely causeWhat to do
Clicking, grinding, beepingDamaged heads or motorPower off; professional lab
Drive not detected, not spinningElectronics or motor failureProfessional lab
Very slow, copies stallWeak or bad sectorsCreate a disk image
Repeated I/O device errorsBad sectors or connectionCheck the cable; then create a disk image
Health status Warning or UnhealthyDrive reports failureCreate a disk image, then replace the drive
Drive disconnects at randomCable, power or failing driveTry other cable and port; if it persists, create a disk image

Frequently asked questions

What is a disk image and why make one?+

A disk image is a complete copy of a drive saved as a file. Making one means a failing drive is read once and all scanning and recovery happen on the copy.

Is it safe to keep scanning a failing drive?+

Repeated scans put more wear on a weak drive and can finish it off. Copy it once with a disk image, then scan the copy.

How much space does the image need?+

Plan for free space equal to the capacity of the drive you copy, on a different, healthy drive.

Can software fix a clicking hard drive?+

No. Clicking points to a mechanical problem. Power the drive off and use a professional data recovery lab.

What happens to sectors that cannot be read?+

They stay empty in the image and are marked as unreadable on the map. Files in those areas come back partly damaged or not at all; DiskMend reports them.

Guides

More guides

Guides →